Microcom 470 Bedienungsanleitung PDF herunterladen

T470 User’s Manual, Part C … AuxIR Device support Page 1

T470User’sManual,PartC…AuxIRDevicesupport…V029release

Ed Schoell, March 18

2015

This manual covers the use of the “RES” pin in IR mode on the JED T470. This can be set to an IR out mode in the

window on the far right of the “Config Utility”. Set “IR Out” as the option in this mode.

It is intended that IR outputs in “AuxIR” mode complement the RS232 drive to the main display device.

So an AuxIR signal can control a projector’s screen, an audio processor (e.g. from Panasonic), an ancillary display or a

set top box, (e.g. a Wintal, a Healing or a Foxtel).

Audio control: In the same way, T470 volume keys can feed Volume Up and Volume Down commands to a

Panasonic, etc. audio controller while the rest of the keys can control a projector or LCD panel via RS232. A third

AuxIR key might be allocated as a power On/Off for the Panasonic device.

Ancillary Display: This IR signal can also control an extra display device, and a key on the T470 can turn power On or

Off on this auxiliary panel, or even select sources on it. (So, in a church, for instance, the main congregation can

watch a projected display controlled via RS232, and an extra key via AuxIR can turn on a smaller LCD display visible to

the choir.)

Set Top Boxes: Thus it is useful when an RS232 controlled projector or LCD/Plasma panel is to have a set top box

(STB) TV tuner as an input, and for that STB TV channel to be stepped up or down from the JED T470 using a couple

of specially setup keys (called “TV Channel Up” and “TV Channel Down”). In this application, a “TV” key should be

provided from the source keys to set the LCD panel/projector to, say, an HDMI or a Composite Video connected to

the STD output. (One could also allocate an AuxIR “Power” key for the STB, to toggle its power on and off, although

this is not necessary: the STD boxes restart in “On” mode on the previous active channel if the power cycles.)

AuxIR setup: The AuxIR device selection is set in the same way as the DisplayDevice, using the Config Utility (but

with a new, adjacent Tab. The selection is also a 4-digit code, which can be entered digit by digit or by using Inc. and

Dec. buttons. The ID of the selected device is shown in the window below the 4-digit code entry. (This version is due

for release early Sept.)

Obviously, a keyboard with AuxIR key allocations must be used. These AuxIR keys are then allocated a function in the

same way sources were allocated to source keys of the display device. The “RES Pin” must be set to “IR Out”.

Note: A debug mode is built into the Configuration Utility: If the RES pin is temporally set to PIR mode, and the

Monitor mode is activated, the T470 will put out debug messages for the AuxIR system consisting of the IR format

and all the bytes in hex of the IR code being set out on the IR LED. This allows comparison for correctness with the

codes in the tables below, as well as Device codes, etc. Don’t forget to set it back to IR after using this debug mode.)

TableofContents

Audio processors

Panasonic 2

AuxIR Display Devices 3

Soniq LCD panel 3

Set Top Boxes

Foxtel IQ2 4

Healing STB HHT894 5

Wintel STB14HD/ Hea. HHT898 6

1 2 3 4 5 6

Inhaltsverzeichnis

Seite 1 - TableofContents

T470 User’s Manual, Part C … AuxIR Device support Page 1 T470User’sManual,PartC…AuxIRDevicesupport…V029releaseEd Schoell, March 18th 201

Seite 2 - Panasonic Audio: Code 2000h

T470 User’s Manual, Part C … AuxIR Device support Page 2 Panasonic Audio: Code 2000h This device controls audio via IR, and needs three AuxIR keys

Seite 3 - Soniq LCD TV : Code 3000h

T470 User’s Manual, Part C … AuxIR Device support Page 3 Soniq LCD TV : Code 3000h This device controls audio via IR, and needs three AuxIR keys all

Seite 4

T470 User’s Manual, Part C … AuxIR Device support Page 4 Foxtel IQ2 Set Top Box : Code 6000h In simple applications, this device just needs Up and D

Seite 5

T470 User’s Manual, Part C … AuxIR Device support Page 5 Healing Set Top Box HTT894 : Code 7F00h In simple applications, this device just needs Up a

Seite 6

T470 User’s Manual, Part C … AuxIR Device support Page 6 Wintal STB14HD / Healing Set Top Box HTT898 : Code 8000h In simple applications, this devic

Weitere Dokumente für Drucken & Scannen Microcom 470

Um das Dokument anzuzeigen Microcom 470 Betreibershandbuch

Microcom 470 Betreibershandbuch (124 Seiten)

Um das Dokument anzuzeigen Microcom 470 Bedienerhandbuch

Microcom 470 Bedienerhandbuch (46 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Microcom 470 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Drucken & Scannen Microcom 470 herunter. T470 User`s Manual, Part C … uxIR Device support … V029 release Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Drucken & Scannen Microcom 470

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Drucken & Scannen Microcom 470