Microcom 814M Betreibershandbuch

MODEL 814M DIRECT THERMAL PRINTER OPERATOR’S MANUAL PART NUMBER 880047-0100 Revised 03/25 JSR © Copyright 20

6 • Marked paper specification In marked paper mode, the printer determines cut position by referencing black mark position. Marked paper shoul

7 3 Structure and Functions 3.1 Appearance 1------------Print unit 2------------Cutter 3------------Cutter l

8 3.2 External Dimensions Figure 3-4 Dimensions Without Paper Holder

9 Figure 3-5 Dimensions of Vertical Structure

10 Figure 3-6 Dimensions of Horizontal Paper Holder

11 3.3 Printer Mechanism 3.3.1 Printer Mechanism (without paper holder) 3.3.2 Printer Mechanism Explanation 1. Print

12 6. Paper load sensor --Detects the front edge of paper. 7. Cutter 8. Power LED (Green) --Indicates whether the power

13 3.4 Presenter 3.4.1 Appearance 1.-- Presenter control board 2.-- Presenter module

14 3.4.2 Presenter Parts Explanation 1. Paper loading sensor –Used to detect paper status. 2. Prsln Sensor (optional) –Used to detect whether pa

15 3. Paper Roll-Spacer Block − Install paper roll-spacer block on paper holder only when using a 210mm wide paper roll. For 216mm wide paper, remo

ii

16 4 Installation 4.1 Unpacking Open the carton and all packing materials, and verify that all items on the packing list are enclosed. In case of dam

17 4.4 Connecting the AC Power Adapter 1. Make sure the printer is turned off. 2. With the flat side of the cable pin of AC adapter facing downw

18 Notes: − When connecting the serial interface cable, do not forget to tighten the retaining screws. For parallel interface cabl

19 2. Insert the paper roll shaft into the core of the paper roll as shown in the following figures: 3. Make sure that the paper wi

20 5. Slide the paper guides to appropriate position (210mm or 216mm) according to paper width (see figure 4-12). 4.6.2 Semi-autom

21 1—Positioning shaft (for horizontal structure only) 2---Paper guides • Manual Paper Loading 1. Turn on the power and the buzzer w

22 − While operating and doing routine maintenance, we suggest reserving space around the printer as follows (see figures 4-16, 4-17 and 4-18).

23 Figure 4-17 Horizontal Structure Figure 4-18 Structure without Paper Holder

24 Notes: − Spaces in above figure include: printer working space, printer routine maintenance and printer operating space. Specifically, printer wo

25 − Paper roll loading space. Make sure to reserve enough space to load the paper roll. − Paper retraction space. The present

iii Proprietary Statement This manual contains information proprietary to Microcom Corporation. This information is intended solely for the use of

26 − Paper roll space Allow space for the paper roll. There is a blue line in the space. If paper feeding is controlled above the blue line, your p

27 − Upper guide “A” dimension of paper out path should be controlled from 4.5 to 5.5 mm and “C” dimension should be from 4 to 5mm.Th

28 4.8 Installing Printer Driver Serial driver and parallel driver both support System platforms such as WINDOWS XP/Vista/7/8. The USB driver suppor

29 5 Routine Maintenance Caution: − Make sure that the power is turned off before starting routine maintenance. − Do not touch the printhead, pla

30 To clean the paper sensor, follow the steps below: • Turn off the power and open the upper cover. • Lift the print head to access the paper en

31 5.2.4 Paper Retract Sensor The paper retract sensor should be cleaned whenever the following circumstances occur: • Paper fail

32 5.3 Cleaning Printing Platen When any of the following case occurs, the sensor should be cleaned: • Print out is not clear. • Some columns o

33 5.5 Manual Removal of the Jammed Paper When any of the errors occurs, please remove jammed paper manually: • Paper jams between platen roller a

34 6.1.2 RS-232 Serial Interface Signals Printer serial port signals and status are described in the following table: 6.2 IEEE

35 6.2.3 Parallel Interface Signals Note: − H stands for host computer terminal and P stands for prin

iv Safety Instructions Before installing and using the printer, please read the following items carefully: • Install the printer on a flat and sta

36 6.2.4 Time Sequence of Data Receiving Signal Time Demands: 6.3 USB Interface (optional) Figure 6

37 6.3.1 Power Interface This connector is used to connect the printer with an external power supply. Power connector pins: Table

38 7.1.2 Problems during Printing Problems Possible reasons How to deal with The receipt cannot be ejected out smoothly. Paper jams. Open u

39 7.1.4 Other Problems Problem Possible reasons How to deal with No power LED and printer does not work. The printer is not connected to the

40 Appendix Self-test Page Print self-test page in the following steps: • Turn off the printer power. • Hold the feed button for at least one s

41 :865,866,1252 :Katakana International Character :U.S.A. :France ;Germany :U.K. :Denmark l :It

42 Font 0(18×34) Font 0 setting Font 1(13×24) Font 1 setting Code Pages Code page type International Character International Char

1 Table of Contents 1 General Description...Page 31.1 Introduction...

2 6 Interface Signal...Page 336.1 RS-232 Interface...

3 1 General Description 1.1 Introduction The 814M is a high performance thermal printer with a cutter and optional presenter. The printer can accept

4 2 Specifications 2.1 Technical Specifications Parameter Items 203dpi Model 300dpi Model Print

5 Note: − DPI: Dots for each inch in printing (one inch equals 25.4 mm) − Character spacing can be adjusted − Actual print